 |
Material Safety Data Sheet
Primeseal Part B
Part B of a 2 part product, must be used in conjunction with part A |
Classified as hazardous material by the NOHSC.
Identification |
| Product Name: |
Primeseal Part B |
| Other Names: |
Duram Primeseal Part B - Hardener |
| U.N. Number: |
N/A |
| Class: |
N/A |
| Hazchem Code: |
N/A |
| Poison Schedule: |
S5 |
| Pack Sizes: |
500ml, 2 litre and 10 litre pails. |
| |
|
|
 |
 |
|
Physical Description |
| Appearance: |
Amber viscous liquid. |
| Boiling Point: |
Similar to water. |
| Vapour Pressure: |
N/A |
| Percent Volatiles: |
< 80% water |
| Specific Gravity: |
1.0 to 1.1 |
| Flash Point: |
> 100 *C |
| Flammability: |
N/A (Water Based) |
| Water Solubility: |
Soluble. |
|
|
|
|
Ingredients |
| Chemical |
CAS No. |
Proportion |
|
| Epoxy Resin
|
25068-38-6 |
+/- 15% |
|
|
| Water
|
|
> 80% |
|
|
|
|
|
|
|
| |
|
|
|
Uses:
To be used in conjunction with Part A to form an excellent 2 Part epoxy primer and sealer. Primeseal Part B is the hardener part of the product. |
Health Warning Information
Health Effects
Swallowed: Single oral dose slightly toxic - low. May cause nausea & vomiting.
Eye: Avoid eye contact - mild to moderate irritation.
Inhaled: Unlikely because of viscous nature of product. Causes irritation to nose and throat, may cause nervous system depression and lung injury.
If cured product is to be sanded then use of an appropriate dust mask is highly recommended ( Class P3 disposable).
Skin: Except for prolonged skin contact causing sensitivity, low molecular weight resins of this type are not anticipated to cause significant adverse effects.
Other: Epoxy resins and diluent may cause sensitisation by skin contact and breathing vapour. For further information contact the Australian Chemical Industry Council's publication 'Epoxy Resins' - Instructions for use, handling and Disposal.
First Aid
Swallowed: Do not induce vomiting. Give plenty of water to drink and seek immediate medical attention. Contact Poisons Information Centre: Australia - 13 11 26 New Zealand - 03 4747 000.
Eye: Immediately thoroughly flush the eye, holding open the lid to ensure any trapped product may be flushed away. If irritation occurs seek medical attention.
Skin: Remove contaminated clothing, wash with soap and water. Do not use solvents to remove material.
Inhaled: Remove person to fresh air and seek immediate medical attention.
Advice to Doctor
Treat symptomatically.
Other Health Information:
Epoxy resins and diluent may cause sensitisation by skin contact and breathing vapour. For further information about epoxy coatings coatings contact Australian Chemical Industry Council's publication 'Epoxy Resins - Instruction For use, handling and disposal'.
Precautions in Use
Engineering Controls:
Use product for it's intended application. Ensure good industrial hygiene and procedures are in practice. Apply in well ventilated areas.
Exposure Limits
N/A
Ventilation
Ensure adequate ventilation when applying finished product.
Personal Protection
The use of rubber gloves, safety boots, goggles and coveralls is recommended.
Safe Handling Information
Storage and Transport
Store in cool dry area in sealed containers which are labeled and leak free.
Suitable containers: Plastic pails as recommended by the manufacturer.
Product not flammable.
Spills and Disposal
Do not allow product to enter drains or waterways. Soak up material with absorbent material such as sand and collect in suitable containers for disposal. Dispose of in accordance to local council regulations.
Fire / Explosion Hazard
Extinguishing media/ hazardous combustion products: Water mist, foam, carbon dioxide, carbon monoxide, phenolic, and possible other toxic gasses and vapours on burning. Product should not decompose explosively. Product will only burn after 80% of liquid has evaporated.
Product should not decompose explosively.
Flammability: Product is water based.
Issued: 1 May 2007 | Valid to: 31 May 2011
Conditions of Use and Disclaimer
The information contained in this Material Data Sheet is given in good faith based upon our current knowledge and does not imply warranty, express or implied. The information is provided and the product is sold on the basis that the product is used for its intended purpose and is used in a proper workmanlike manner in accordance with the instructions of the Product Data Sheet in suitable and safe working conditions. Under no circumstances will the Company be liable for loss, consequential or otherwise, arising from the use of the product.