 |
Material Safety Data Sheet
Maxibond
Bonding agent to ehnace the adhesion properties of subsequent coatings. |
Not Classified as hazardous according to the critera of Worksafe Australia.
Identification |
| Product Name: |
Maxibond |
| Other Names: |
Duramax MaxiBond |
| U.N. Number: |
N/A |
| Class: |
N/A |
| Hazchem Code: |
N/A |
| Poison Schedule: |
Not Scheduled. |
| Pack Sizes: |
4ltr & 15 ltr Pails. |
| |
|
|
 |
 |
|
Physical Description |
| Appearance: |
Milky coloured liquid, practically odourless. |
| Boiling Point: |
+-100% (Relates to water) |
| Vapour Pressure: |
N/A - for water. |
| Percent Volatiles: |
+-60% (Water) |
| Specific Gravity: |
+-1.0 to 1.02 |
| Flash Point: |
N/A( Water Based) |
| Flammability: |
N/A (Water Based) |
| Water Solubility: |
Miscible. |
|
|
|
|
Ingredients |
| Chemical |
CAS No. |
Proportion |
|
| Water.
|
N/A |
>45% |
|
|
| Carboxylated copolymer (butidiene and styrene)
|
N/A |
>45% |
|
|
| Minor Ingredients
|
N/A |
< 10% |
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
Uses:
Liquid adhesion enhancer (bonding agent) and primer for subsequent architectural coatings and renders. |
Health Warning Information
Health Effects
Swallowed: Irritating and nauseating. Single dose oral toxicity is regarded as low.
Eye's: Irritating, Corneal damage is unlikely.
Skin Contact: Minor irritation, prolonged contact should be avoided.
Inhaled: Can be irritating, adverse effects not anticipated.
First Aid
Inhalation: Unlikely due to the nature of the product. Move person to fresh air. If breathing stops, apply artificial respiration. Seek immediate medical advise.
Eye: Flush eye's with clean water holding open to remove product from eye lid. Seek medical help if symptoms persist.
Ingestion: Give milk or water to drink, seek medical attention.
Advice to Doctor
Treat Symptomatically.
Precautions in Use
Low risk. Observe normal industrial hygiene and precautions.
Exposure Limits
The product contains residual traces of styrene, ethyl benzene and 1,3 butadiene. Observe exposure standards:
Styrene: TWA 50 ppm (213 mg/m3) STEL 100 ppm (426 mg/m3)
Etyk Benzene: TWA 100 ppm (434 mg/m3) STEL 125 ppm (543 mg/m3)
1.3 Butadiene: TWA 10 ppm (434 mg/m3) CC2 Carciogen catagory 2.
Ventilation
Ensure adequate fresh ventilation exists . If person is affected by volatiles or smell, (low odour) then remove to fresh air.
Personal Protection
Face mask, goggles (against splashes) and rubber gloves are recommended.
If spraying in confined areas or in misty conditions use an approved mist respirator.
Coveralls and industrial footwear.
Safe Handling Information
Storage and Transport
Store undercover in a cool dry place. Do not allow the product to freeze.
Not considered as a dangerous material for storage purposes.
Suitable containers: Plastic pails as recommended by manufacturer.
Spills and Disposal
Spills: Apply sand to spills and dispose in land fill in accordance with the local council regulation.
Disposal: Can be eliminated from sewage / effluent by chemical flocculation.
Fire / Explosion Hazard
Product is water based no direct hazard.
Issued: 1 May 07 | Valid to: 31 May 2010
Conditions of Use and Disclaimer
The information contained in this data sheet is given in good faith based upon our knowledge and current information and does not imply warranty. The information is provided and the product sold on the basis that the product is used for its intended use and applied in a proper workman like manner in accordance with the instruction in this data sheet onto suitable and correctly prepared surfaces which shall remain sound, stable, free of structural defects, cracking, spalling concrete cancer, negative pressure, movement or other conditions that may effect the performance of the product. Deviations from application instructions may diminish or negate the performance of the product. Under no circumstances will the Company be liable for any loss, consequential or otherwise, arising from the use of the product. Liability is limited to the replacement of proven faulty product.