 |
Product Data Sheet
Finesse
Spray-on 'sand-stone' finish texture coating |
Description
Duramax FINESSE is a decorative, highly durable acrylic coating which when sprayed (usually sprayed but can be trowelled) provides a refined and sylish coloured 'sandstone' appearance in a sand textured finish. Finesse does not require to be top coated, but surfaces must be primed prior to the application of FINESSE.
Uses
FINESSE maybe used on suitably primed internal and external walls providing a decorative, protective coating/finish.
Suitable Surfaces
FINESSE is suitable to be applied to primed, sound off form concrete, cement render, fibre - cement sheeting, Harditex sheeting, other concrete products and brick surfaces.
Substrate or joints may need to be prepared with MAXIJOINT and/or MAXICRETE.
NB: See appropriate Product Data Sheets.
Specification
The information contained in this product data sheet is typical but does not constitute a full specification as conditions and specific requirements may vary from project to project. The instructions should be considered as a minimum requirement but the applicator or contractor must use their skill, knowledge and experience to carry out additional works as may be necessary to meet the requirements of the project. Specification for specific projects should be sought from the Company in writing.
Limitations
Ambient temperature: Min. 10oC Max. 35oC.
Surface temperature: Min. 5oC Max. 50oC
Do not apply if rain or frost is imminent or possible before product has properly dried. The product should not be subjected to hydrostatic pressure and excessive rising damp.
Not suitable for foot traffic.
Benefits and Advantages
Ease of application.
Excellent adhesion to primed surface.
Excellent weathering & abrasion resistance.
Allows surface to breathe.
Application safety, water based, non combustable.
High tensil strength.
Precautions in Use
The use of gloves and goggles is recommended as the product may irritate skin and eyes.
Priming and Surface Preparation
Good preparation is essential. Surfaces must be sound, stable, dry, clean and free of dust, loose, flaking, friable material and substances that may diminish adhesion.
Prime surface with MAXIPRIME which maybe tinted as close as possibe to the FINESSE colour. Allow to dry for approximately 4 hours before top coating.
Application
Apply FINESSE either by hopper spray or trowel. Spray evenly over the surface using cross - lap technique. Spray is best suited to hide structual imperfections. If required, up to 10% clean water maybe added to assist with sprayability. Use plastic trowel only if substrate is free from imperfections. It is recommended that the product be throughly stirred using a power stirrer.
Application Experience
We recommend that the product is applied by person with the appropriate skills and experience for the type of product. The acceptability of the surface is the responsibility of the applicator.
Coverage
The stated average coverage rate may vary depending upon type, condition, porosity, texture of the surface and application technique.
Average approximate spread rate is 14 to 18 sq. m per 15 litre pail. But this may vary dependent upon type, condition and porosity of the substrate and application technique.
MAXIPRIME: Undiluted - 6 to 8 sq. m per litre .
Diluted - +/- 14 sq. m per litre with the addition of 30% clean water.
Colours
Available in a wide range of colours, made to order.
Colour Batches
Whilst care is taken to accurately colour match, batch to batch variations may occur for reasons which may be beyond our control. We strongly advise that project requirements are ordered in a single batch lot to avoid colour matching from batch to batch. Minimum quantities and tinting charges may apply.
Contractor Responsibility
It is the responsibility of the contractor or applicator to ensure that the colour is within specification prior to its application. The Company shall not be liable for any colour variations after the product has been applied. Further, the applicator should use product for touch-ups from the same batches used to do the original coats.
Drying and Curing
Drying and curing of the product is affected by type, dryness and porosity of the surface, temperature, humidity, ventilation, climate conditions and application technique and therefore drying and curing can only be given as a guide.
Touch Dry: 2 to 4 hours at 20oc
Recoat: 24 hours
Hard Dry: 2 to 4 days
Storage
Store in dry, cool area and protect from heat, frost, moisture and damage.
Available in 15 Lt Pails.
Shelf Life: 6 months in unopened containers.
Containers should be rotated to prevent settlement.
Clean Up
Wet spills can be cleaned with water. Ensure product does not enter the drains. Care must be taken to avoid damaging the coating.
Safety & Precautions
The use of gloves and goggles is recommended as the product may irriate skin and eyes.
If product is in eyes, flush with thoroughly with clean water, holding open lid to ensure any trapped product will be flushed away.
If on skin, remove contaminated clothing and wash with soap and water. Do not use solvent.
If inhaled, unlikely due to the viscosity of the product, remove person to fresh air and apply artificial respiration if required.
For full safety data refer to the products Material Safety Data Sheet. Observe precautions as per label.
Issued: 1 May 2007 | Valid to:
Conditions of Use and Disclaimer
The information contained in this data sheet is given in good faith based upon our knowledge and current information and does not imply warranty. The information is provided and the product sold on the basis that the product is used for its intended use and applied in a proper workman like manner in accordance with the instruction in this data sheet onto suitable and correctly prepared surfaces which shall remain sound, stable, free of structural defects, cracking, spalling concrete cancer, negative pressure, movement or other conditions that may effect the performance of the product. Deviations from application instructions may diminish or negate the performance of the product. Under no circumstances will the Company be liable for any loss, consequential or otherwise, arising from the use of the product. Liability is limited to the replacement of proven faulty product.